Jasper II SID PRO S

The Jasper II 1:1 SATA/IDE HDD/SSD Duplicator PRO S is one of the most versatile drive duplicators in the market. This duplicator can be used to copy practically any SATA or IDE HDD/SSD in 3.5" or 2.5" form factor. The included Diamond Cipher II enclosures (drive carrier) also enable copying data directly to or from a hard drive with AES 256-bit hardware encryption. Using Addonics optional 2.5" flash drive kits, this duplicator can copy a variety of popular flash media such as M2 SATA SSD, mSATA SSD, CFast card, CF card, Micro SATA HDD/SSD or slim SATA SSD.

Similar to other members of the Addonics HDD Duplicator family, this PRO S model is also simple to use and operate. Just load your master hard drive to the source drive bay and another hard drive of capacity equal or larger than the source drive to the target drive bay, turn the key lock on each drive bay to the lock position and push the start button to start the copying process.

Front view
(shown with Diamond Cipher II enclosure in top bay)
  Rear view

 

  • Top bay supports SATA, IDE or Addonics AES 256-bit encrypted drive using the included Diamond SATA, IDE or Diamond Cipher II drive enclosure
  • Bottom bay is a Snap-In drive bay that supports 3.5" SATA HDD or 2.5" SATA HDD/SSD via a included 2.5" - 3.5" drive adapter. Drive is directly loaded into the drive bay without any special tool.
      

 

  • Top and bottom bays can be set to either Source or Target bay depending on the Source/Target switch setting on the back of the unit

The following drive enclosures are included in this duplicator: Diamond SATA Drive enclosure (DSACSB), Diamond IDE Drive enclosure( DICSB) and Diamond Cipher II Drive enclosure (DCSA6GCS). These drive enclosures are for loading into the top bay. With these enclosures, the top bay can use either SATA, IDE or Diamond Cipher II encrypted drive in 3.5" or 2.5" form factor as a source drive when the top bay is set as source bay (factory default setting) or as a target drive when the top bay is set as a target bay.

 

  • Copy any 2.5" or 3.5" hard drive / SSD to any 2.5" or 3.5" hard drive or SSD with AES 256-bit encryption and vice versa*
  • Great for cloning hard drives, making back up hard drives, system upgrade, and data distribution
  • Top bay supports SATA, IDE or Addonics AES 256-bit encrypted drive using the included Diamond SATA, IDE or Diamond Cipher II drive enclosure
  • Bottom bay is a Snap-In drive bay that supports 3.5" SATA HDD or 2.5" SATA HDD/SSD via an optional 2.5" - 3.5" drive adapter (AE25SN35SA). Drive is directly loaded into the drive bay without any special tool.
  • Top and bottom bay can be set to either as Source or Target bay depending on the Source/Target switch setting on the back of the unit
  • Any eSATA drive can be attached to the Source or Target port on the back of the unit for use as a Source or Target drive
  • Support any type of file format
  • Typical copying speed1 ~ 250 MB/sec (actual speed depends on the performance of the drive)
  • No drive capacity limitation
  • Drive sanitizing:
      • SECURE ERASE - HDD duplicator sends a WIPE command to the hard drive. This command fills 00 string to entire HDD
      • OVERWRITE - One pass, 3 passes, and 7 passes 5220.22-M.  The duplicator writes a string of pattern over the entire disk one time, three times or seven times.5220.22-M is the DoD standard for drive sanitization
      • Encryption*
  • LCM control module provides a rich set of robust advanced configuration options (click Full LCD console feature list to see the complete list of the duplicator functions)
  • Operate as a stand-alone appliance. No computer or software needed

 

* This Duplicator PRO-S comes with all necessary drive enclosures to copy data from a hard drive with no encryption to another hard drive with AES 256-bit encryption to secure your data. To do so all is needed is to install a standard hard drive in the source bay (the bottom bay set as source) and a target drive into the Diamond Cipher II enclosure (top bay set as the target). The data copied into the drive inside the Diamond Cipher II enclosure will automatically be encrypted. Please note that all the information encrypted with the Diamond Cipher can only be accessible with Diamond Cipher enclosure or the Addonics Cipher Chain. To understand the detail on how to encrypt the hard drive with a Diamond Cipher II  drive kit or Cipher Chain II, please visit the Diamond Cipher II and Cipher Chain II web pages.

Please note that if the AES 256-bit Diamond Cipher II enclosure is used as a source, the hard drive inside must already be an encrypted hard drive prepared with the Diamond Cipher II enclosure, putting a regular hard drive inside the Diamond Cipher II enclosure to use as a source will result in copying a blank drive.

 

1. The speed here is for reference only. The speed was measured basing on using 3.5" SATA III 250 GB hard drive for both source and target. The transfer rate varies depending on the speed of the source and destination drive 

  • Writing mode : Sector to Sector
  • Typical copying speed ~ 250 MB/sec (actual speed depends on the performance of the drive)
  • Stylish clear acrylic exterior
  • Light weight and sturdy aluminum construction
  • Ventilated side panels for efficient air flow
  • Ball bearing high CFM low noise cooling fans
  • LCD display with functional control panel
  • Integrated 150W 110/240 AC power supply
  • Compact size (W x D x H): ~ 8.19 x 11.75 x 8 inch  (208 x 298 x 203 mm) 
  • Weight: ~ 8.3 lb (3.76 kg)
  • Operating environment: 0 - 50 degree C, 15% - 90% RH
  • Storage environment: (- 20) - (65) degree C, 0% - 95% RH non-condensing

PRODUCTS

JD2-SIDAES - (Jasper II SIDAES - 1:1 3.5"/2.5" SATA/IDE HDD/SSD duplicator PRO)
Content:Jasper II 1:1 3.5"/ 2.5" HDD/SSD High Speed Duplicator main unit, 1 Diamond SATA drive enclosure(DSACSB), 1 Diamond Cipher II SATA drive enclosure (DCSA6GCS), 1 Diamond IDE drive enclosure (DICSB), 1 44pin - 40pin IDE connector (AA25IDE35), power cord, user guide
Price: 669.00

ACCESSORIES

DICSB (Diamond encl. for 3.5" IDE hdd, black)
DICSB Diamond enclosure for 3.5" IDE hard drive (black)
Price: 39.00
DSACSB (Diamond encl. for 3.5" SATA hdd, black)
DSACSB Diamond enclosure for 3.5" SATA hard drive (black)
Price: 24.99
DCSA6GCS (Diamond Cipher II 6G enclosure, AES 256-bit encryption)
Content: Diamond Cipher II 6G enclosure with 256-bit AES encryption. This is enclosure only. Cipher key is not included.
Price: 89.00
AD25M2MSA (2.5" M2 / mSATA Flash drive kit)
Content: 2.5" M2 / mSATA flash drive kit with easy media installation or removal design (black color), user guide
Price: 27.95
AD25CFASTD-N (2.5" CFast HDD kit, open end, black )
Content: 2.5" CFast hard drive kit with open end black color bracket for easy media nstallation, user guide.
Price: 24.95
AD25CFD-N (2.5" CF HDD PRO, easy media insertion and removal, black color)
Content: 2.5" CF hard drive kit with black color bracket and open end for easy media installation.
Price: 26.95
AD18M25S (1.8" micro SATA - 2.5" SATA HDD adapter)
Content: 1.8" micro SATA - 2.5" SATA HDD adapter,
Price: 19.00
AA25SEMBK (Slim SATA SSD 2.5" HDD adapter)
Content: 2.5" HDD adapter kit for slim SATA embedded SSD, user guiode
Price: 19.00
Drivers
Jasper II duplicator firmware
Applies to:

For all Jasper II duplicator except the model JD2P3

Firmware update procedures:

  1. download and unzip the firmware file
  2. copy the firmware file (.BIN file) onto a HDD or SSD formatted in FAT32 (DO NOT USE NTFS or any other file system)
  3. on the duplicator contorl panel, go to Utility/System Update and follow the onscreen instructions